Das Herbstsemester 2020 findet in einer gemischten Form aus Online- und Präsenzunterricht statt.
Bitte lesen Sie die publizierten Informationen zu den einzelnen Lehrveranstaltungen genau.

Reza S. Abhari: Katalogdaten im Herbstsemester 2016

NameHerr Prof. Dr. Reza S. Abhari
LehrgebietAerothermodynamik
Adresse
Institut für Energietechnik (eh.)
ETH Zürich, ML J 35
Sonneggstrasse 3
8092 Zürich
SWITZERLAND
Telefon+41 44 632 26 91
E-Mailrabhari@lec.mavt.ethz.ch
DepartementMaschinenbau und Verfahrenstechnik
BeziehungOrdentlicher Professor

NummerTitelECTSUmfangDozierende
151-0123-00LExperimental Methods for Engineers4 KP2V + 2UT. Rösgen, R. S. Abhari, K. Boulouchos, D. J. Norris, H.‑M. Prasser, A. Steinfeld
KurzbeschreibungThe course presents an overview of measurement tasks in engineering environments. Different concepts for the acquisition and processing of typical measurement quantities are introduced. Following an initial in-class introduction, laboratory exercises from different application areas (especially in thermofluidics and process engineering) are attended by students in small groups.
LernzielIntroduction to various aspects of measurement techniques, with particular emphasis on thermo-fluidic applications.
Understanding of various sensing technologies and analysis procedures.
Exposure to typical experiments, diagnostics hardware, data acquisition and processing.
Study of applications in the laboratory.
Fundamentals of scientific documentation & reporting.
InhaltIn-class introduction to representative measurement techniques in the
research areas of the participating institutes (fluid dynamics, energy technology, process engineering)
Student participation in 8-10 laboratory experiments (study groups of 3-5 students, dependent on the number of course participants and available experiments)
Lab reports for all attended experiments have to be submitted by the study groups.
A final exam evaluates the acquired knowledge individually.
SkriptPresentations, handouts and instructions are provided for each experiment.
LiteraturHolman, J.P. "Experimental Methods for Engineers", McGraw-Hill 2001, ISBN 0-07-366055-8
Morris, A.S. & Langari, R. "Measurement and Instrumentation", Elsevier 2011, ISBN 0-12-381960-4
Eckelmann, H. "Einführung in die Strömungsmesstechnik", Teubner 1997, ISBN 3-519-02379-2
Voraussetzungen / BesonderesBasic understanding in the following areas:
- fluid mechanics, thermodynamics, heat and mass transfer
- electrical engineering / electronics
- numerical data analysis and processing (e.g. using MATLAB)
151-0203-00LTurbomachinery Design Belegung eingeschränkt - Details anzeigen
Maximale Teilnehmerzahl: 20
4 KP2V + 1UR. S. Abhari, N. Chokani, B. Ribi
KurzbeschreibungDie Vorlesung bietet eine Einführung in die Grundlagen und das Design von Turbomaschinen.
LernzielGrundlagen verstehen, und Designprozesse und Verhalten von Turbomaschinen lernen.
InhaltDiese Vorlesung beschreibt die Grundlagen des Designs von Turbomaschinen (Turbinen und Verdichtern). Dazu werden zunächst die theoretischen Grundlagen vertieft erarbeitet. Ausgehend von den thermodynamischen Grundlagen werden Verlustkorrelationen und -Mechanismen behandelt. Diese Grundlagen führen zu einem Verständnis des 3D Design der Turbomaschinen.
Im zweiten Teil der Vorlesung wird das Verhalten der Turbomaschinen bei veränderten Betriebsbedingungen dargestellt. Ebenfalls behandelt werden mechanische Fragestellungen des Turbomaschinenbaus wie z.B. Vibrationen, Lagerbelastungen und auftretende Spannungen in den Bauteilen.
SkriptVorlesungsunterlagen
151-0243-00LNew Enterprises for Engineers Information
Findet dieses Semester nicht statt.
4 KP3GR. S. Abhari
KurzbeschreibungTransforming Needs to opportunities for new technology enterprises.
- Links between entrepreneurship and product development/engineering.
- Sales, marketing, financing, and growth. Detailed Plans and execution.
- Survival through cash flow management.
- Human issues in new enterprise
- Alignment of interests.
- Transition of enterprises along growth path
- http://www.NEFE.ethz.ch
LernzielTransforming Needs to Business Enterprises

Goals of the course:
- Propose the role of Needs-Driven Opportunities for new technology enterprises
- Explore links between entrepreneurship and engineering; such as problem solving, planning, system analysis, can-do attitude!
- Making it happen- through sales, marketing, planning, staffing, implementation, financing, and growth. Detailed Plans and execution
- Survival (and success) through cash flow management
- Explore the human issues in any new enterprise
- Alignment of interests between providers of value (founders and staff, VC’s) and the providers of capital (Angels, VC’s, Corporation)
- Transformations of enterprises along growth path
InhaltApproach:
Weekly lectures including discussions of international case studies
Exercises to develop and present modules of new plans
Extensive class interactions capped with presentation by each (group) student of new enterprise plan

Please see http://www.NEFE.ethz.ch
SkriptCourse material will be communicated to the students prior to the start of each class for download.
Voraussetzungen / BesonderesThis course is primarily for engineering and natural science students at all levels who are interested in participating in the initiation or growth of a new enterprise. The new enterprise could be stand -alone start up or a new business unit for an existing enterprise.

The class is practical in nature but emphasizes the basic understanding of the parameters that significantly contribute to the success of a new enterprise. It will be highly interactive with special selected guests from Selected guests from; companies founder, venture capital and business angel, and large corporation executive. Class attendance and active participation is required.
151-0261-00LThermodynamics III3 KP2V + 1UR. S. Abhari, A. Steinfeld
KurzbeschreibungUntersuchung der technischen Anwendungen und Erweiterung der Grundlagen, die in Thermodynamik I und II erarbeitet wurden.
LernzielDas Verständnis und Anwenden von thermodynamischen Prinzipien und Prozessen für Kreisprozesse, die in der Praxis benutzt werden.
InhaltWärmestrahlung, Wärmetauscher, Gasgemische & Psychrometrie, Dampf Prozesse, Gasturbinen Prozesse, Verbrennungsmotoren, Wärmepumpen
151-0906-00LFrontiers in Energy Research
This course is only for doctoral students.
2 KP2SM. Mazzotti, R. S. Abhari, J. Carmeliet, M. Filippini
KurzbeschreibungPhD students at ETH Zurich working in the broad area of energy present their research to their colleagues, to their advisors and to the scientific community.
LernzielKnowledge of advanced research in the area of energy.
InhaltPhD students at ETH Zurich working in the broad area of energy present their research to their colleagues, to their advisors and to the scientific community. Every week there are two presentations, each structured as follows: 15 min introduction to the research topic, 15 min presentation of the results, 15 min discussion with the audience.
SkriptSlides will be distributed.
151-1053-00LThermo- and Fluid Dynamics Information 0 KP2KP. Jenny, R. S. Abhari, K. Boulouchos, P. Koumoutsakos, C. Müller, H. G. Park, D. Poulikakos, H.‑M. Prasser, T. Rösgen, A. Steinfeld
KurzbeschreibungCurrent advanced research activities in the areas of thermo- and fluid dynamics are presented and discussed, mostly by external speakers.
LernzielKnowledge of advanced research in the areas of thermo- and fluid dynamics
860-0003-00LCornerstone Science, Technology, and Policy Belegung eingeschränkt - Details anzeigen
Only for Science, Technology, and Policy MSc.
2 KP2ST. Bernauer, R. S. Abhari
KurzbeschreibungThis course introduces students to the MSc program in two ways. First, it provides a general introduction to the study of STP. Second, it exposes students to a variety of complex policy problems and ways and means of coming up with proposals for and assessments of policy options.
LernzielThis course introduces students to the MSc program in two ways. First, it provides a general introduction to the study of STP. Second, it exposes students to a variety of complex policy problems and ways and means of coming up with proposals for and assessments of policy options.
InhaltDay 1: Introduction to the study of Science, Technology and Policy / getting to know each other, social event
Day 2: Knowledge assessment in areas marked by controversy over scientific evidence
Day 3: Challenges of urban development / Energy transition and sustainable mobility
Day 4: Mitigating and adapting to climate change / Managing international water resources
Day 5: Implications of digital society / Policy planning exercise
Voraussetzungen / BesonderesReserved for the ISTP's Master students
860-0004-00LBridging Science, Technology, and Policy Belegung eingeschränkt - Details anzeigen
Only for Science, Technology, and Policy MSc.
3 KP2SR. S. Abhari, T. Bernauer
KurzbeschreibungThis course focuses on technological innovations from the beginning of humanity through the industrial revolution up until today. It provides students with a deeper understanding of the factors that drive technological innovations, and the roles government policies, society, science, and industry play in this regard.
LernzielThis course picks up on the ISTP Cornerstone Science, Technology and Policy course and goes into greater depth on issues covered in that course, as well as additional issues where science and technology are among the causes of societal challenges but can also help in finding solutions.
InhaltWeek 1: no class because of ISTP Cornerstone Science, Technology and Policy course
Week 2: technology & society in historical perspective - technological innovations up to the industrial revolution
Week 3: technology & society in historical perspective - technological innovations during the industrial revolution - engines & electricity
Week 4: technology & society in historical perspective - from the industrial revolution to modernity - mobility and transport (railroads, ships, cars, airplanes, space)
Week 5: food production: the green revolutions.
Week 6: microelectronics, computing & the internet
Week 7: life sciences: pharmaceuticals & diagnostic technology
Week 8: energy: primary fuels, renewables, networks
Week 9: automation: self-driving cars & trains, drones
Week 10: communication & Big Data: semiconductors and software
Week 11: military & security issues associated with technological innovation
Week 12: possible futures (1): nuclear fusion, geoengineering
Week 13: possible Future (2): information, communication, robotics, synthetic biology, nanotech, quantum computing
SkriptCourse materials will be given to the students prior to the start of each class
860-0005-00LColloquium Science, Technology, and Policy (HS) Belegung eingeschränkt - Details anzeigen
Students of Science, Technology, and Policy MSc have priority.
1 KP2KT. Bernauer, R. S. Abhari
KurzbeschreibungPresentations by invited guest speakers from academia and practice/policy. Students are assigned to play a leading role in the discussion and write a report on the respective event.
LernzielPresentations by invited guest speakers from academia and practice/policy. Students are assigned to play a leading role in the discussion and write a report on the respective event.
InhaltSee program on the ISTP website: http://www.istp.ethz.ch/news-and-events/events.html
Voraussetzungen / Besonderesopen to anyone from ETH