151-0059-10L  Engineering Tool: CAD-Methodology and PDM-Technology in the Focus Project

SemesterAutumn Semester 2020
LecturersM. Schütz
Periodicityyearly recurring course
Language of instructionGerman
CommentAll Engineering Tools courses are for MAVT Bachelor’s degree students only.

Number of participants limited to 25.



Courses

NumberTitleHoursLecturers
151-0059-10 KIngenieur-Tool: CAD Methodik und PDM-Einsatz im Fokusprojekt
Blockkurs in der ersten Semesterwoche
Die Teilnehmer sollten in Fokusprojekten involviert sein. Falls nicht, bitte bei den Dozierenden anfragen.
Die genauen Unterrichtszeiten von ONLINE - Veranstaltungen werden von den Dozierenden kommuniziert.
12s hrs
15.09.14:00-18:00ON LI NE »
16.09.14:00-18:00ON LI NE »
17.09.14:00-18:00ON LI NE »
M. Schütz

Catalogue data

AbstractThe participants learn about the procedures and tools that are necessary to develop technical products. The focus is on computer-based design and development and the management in an integrated software environment.
ObjectiveThe participants will deepen their existing CAD knowledge and learn new PDM knowledge, so that these may be directly applied and used in the focus project.
- CAD refresh (Modelling, Assembling, Drafting, etc.) and CAD mythology for construction (Top-Down modelling)
- Introduction to the Team Center (Siemens PDM System)
- TeamCenter data flow, in particular the process of creating and managing new Items and Parts, the approval procedure and creating different versions of Parts
The participants will learn and experiment with procedures by working on concrete examples so that they will subsequently be able to begin with independent product construction.
The following topics will be dealt with in depth in the lectures supporting the focus project (Praxiskurs): CAD-Methodology, FE calculations, motion simulation and construction methodology.
Content1. Afternoon: CAD refresher and top down modelling
- To refresh already existing knowledge of CAD functionality.
i. Sketch and features as well as manipulation and optimizing models.
ii. Assembling
iii. Drafting.
iv. Organisation. working methods, conventions.

-Top down modelling CAD
i. Introduction to top down modelling and concept modelling
ii. Case study of top down modelling

2.Afternoon: Introduction to TC (Team Center)
- Introduction: Short introduction to PLM (What is the idea of PLM? PLM is more than the pure management of drawings!).
- Lesson 1 - Team Center Rich Client Interface
- Lesson 2 - TC data types
- Lesson 3 - Construction from data in TC
- Lesson 4 - Searching for and examining data.

3.Afternoon: TC application
- Lesson 5 - Unit lists (PSE)
- Lesson 6 - Cross-referencing
- Lesson 7 - Data release
- Lesson 8 - Product data examination
Prerequisites / Notice- at least two students of a Focus-Team should sign in for this course, if teh use of Siemens TeamCenter PLM is given for the Team.
- only for students participating in a Focus Project in the same semester
- not more than 25 students

Performance assessment

Performance assessment information (valid until the course unit is held again)
Performance assessment as a semester course
ECTS credits0.4 credits
ExaminersM. Schütz
Typeungraded semester performance
Language of examinationGerman
RepetitionRepetition only possible after re-enrolling for the course unit.

Learning materials

No public learning materials available.
Only public learning materials are listed.

Groups

No information on groups available.

Restrictions

Places25 at the most
PriorityRegistration for the course unit is only possible for the primary target group
Primary target groupMechanical Engineering BSc (152000)
Waiting listuntil 07.09.2020
End of registration periodRegistration only possible until 18.09.2020

Offered in

ProgrammeSectionType
Mechanical Engineering BachelorEngineering ToolsWInformation